The following data types shall be defined through typedef:

cc_t

Used for terminal special characters.

speed_t

Used for terminal baud rates.

tcflag_t

Used for terminal modes.

The above types shall be all unsigned integer types.

The implementation shall support one or more programming environments in which the widths of cc_t, speed_t, and tcflag_t are no greater than the width of type long. The names of these programming environments can be obtained using the confstr() function or the getconf utility.

The termios structure shall be defined, and shall include at least the following members:

tcflag_t c_iflag Input modes. tcflag_t c_oflag Output modes. tcflag_t c_cflag Control modes. tcflag_t c_lflag Local modes. cc_t c_cc[NCCS] Control characters.

A definition shall be provided for:

NCCS

Size of the array c_cc for control characters.

The following subscript names for the array c_cc shall be defined: center;c s l. Subscript Usage l l l. Canonical Mode Non-Canonical Mode Description VEOF EOF character. VEOL EOL character. VERASE ERASE character. VINTR VINTR INTR character. VKILL KILL character. VMIN MIN value. VQUIT VQUIT QUIT character. VSTART VSTART START character. VSTOP VSTOP STOP character. VSUSP VSUSP SUSP character. VTIME TIME value.

The subscript values shall be unique, except that the VMIN and VTIME subscripts may have the same values as the VEOF and VEOL subscripts, respectively.

The following flags shall be provided.

The c_iflag field describes the basic terminal input control:

BRKINT

Signal interrupt on break.

ICRNL

Map CR to NL on input.

IGNBRK

Ignore break condition.

IGNCR

Ignore CR.

IGNPAR

Ignore characters with parity errors.

INLCR

Map NL to CR on input.

INPCK

Enable input parity check.

ISTRIP

Strip character.

IXANY

Enable any character to restart output.

IXOFF

Enable start/stop input control.

IXON

Enable start/stop output control.

PARMRK

Mark parity errors.

The c_oflag field specifies the system treatment of output:

OPOST

Post-process output.

ONLCR

Map NL to CR-NL on output.

OCRNL

Map CR to NL on output.

ONOCR

No CR output at column 0.

ONLRET

NL performs CR function.

OFILL

Use fill characters for delay.

NLDLY

Select newline delays:

NL0

Newline type 0.

NL1

Newline type 1.

CRDLY

Select carriage-return delays:

CR0

Carriage-return delay type 0.

CR1

Carriage-return delay type 1.

CR2

Carriage-return delay type 2.

CR3

Carriage-return delay type 3.

TABDLY

Select horizontal-tab delays:

TAB0

Horizontal-tab delay type 0.

TAB1

Horizontal-tab delay type 1.

TAB2

Horizontal-tab delay type 2.

TAB3

Expand tabs to spaces.

BSDLY

Select backspace delays:

BS0

Backspace-delay type 0.

BS1

Backspace-delay type 1.

VTDLY

Select vertical-tab delays:

VT0

Vertical-tab delay type 0.

VT1

Vertical-tab delay type 1.

FFDLY

Select form-feed delays:

FF0

Form-feed delay type 0.

FF1

Form-feed delay type 1.

The input and output baud rates are stored in the termios structure. These are the valid values for objects of type speed_t. The following values shall be defined, but not all baud rates need be supported by the underlying hardware.

B0

Hang up

B50

50 baud

B75

75 baud

B110

110 baud

B134

134.5 baud

B150

150 baud

B200

200 baud

B300

300 baud

B600

600 baud

B1200

1200 baud

B1800

1800 baud

B2400

2400 baud

B4800

4800 baud

B9600

9600 baud

B19200

19200 baud

B38400

38400 baud

The c_cflag field describes the hardware control of the terminal; not all values specified are required to be supported by the underlying hardware:

CSIZE

Character size:

CS5

5 bits

CS6

6 bits

CS7

7 bits

CS8

8 bits

CSTOPB

Send two stop bits, else one.

CREAD

Enable receiver.

PARENB

Parity enable.

PARODD

Odd parity, else even.

HUPCL

Hang up on last close.

CLOCAL

Ignore modem status lines.

The implementation shall support the functionality associated with the symbols CS7, CS8, CSTOPB, PARODD, and PARENB.

The c_lflag field of the argument structure is used to control various terminal functions:

ECHO

Enable echo.

ECHOE

Echo erase character as error-correcting backspace.

ECHOK

Echo KILL.

ECHONL

Echo NL.

ICANON

Canonical input (erase and kill processing).

IEXTEN

Enable extended input character processing.

ISIG

Enable signals.

NOFLSH

Disable flush after interrupt or quit.

TOSTOP

Send SIGTTOU for background output.

The following symbolic constants for use with tcsetattr() are defined:

TCSANOW

Change attributes immediately.

TCSADRAIN

Change attributes when output has drained.

TCSAFLUSH

Change attributes when output has drained; also flush pending input.

The following symbolic constants for use with tcflush() shall be defined:

TCIFLUSH

Flush pending input.

TCIOFLUSH

Flush both pending input and untransmitted output.

TCOFLUSH

Flush untransmitted output.

The following symbolic constants for use with tcflow() shall be defined:

TCIOFF

Transmit a STOP character, intended to suspend input data.

TCION

Transmit a START character, intended to restart input data.

TCOOFF

Suspend output.

TCOON

Restart output.

The following shall be declared as functions and may also be defined as macros. Function prototypes shall be provided.

speed_t cfgetispeed(const struct termios *); speed_t cfgetospeed(const struct termios *); int cfsetispeed(struct termios *, speed_t); int cfsetospeed(struct termios *, speed_t); int tcdrain(int); int tcflow(int, int); int tcflush(int, int); int tcgetattr(int, struct termios *);

pid_t tcgetsid(int);

int tcsendbreak(int, int); int tcsetattr(int, int, const struct termios *);

The following sections are informative.