aprsdigi - APRS(â„¢) digipeater

aprsdigi options

Aprsdigi is a specialized Amateur Packet Radio (AX.25) UI-frame digipeater for the Automatic Position Reporting Systems, APRS(tm). It uses the Linux kernel AX.25 network stack as well as the SOCK_PACKET facility to listen for packets on one or more radio interfaces (ports) and repeat those packets -- with several possible modifications -- on the same or other interfaces. Aprsdigi can also use the Internet to tunnel connections among other APRS digipeaters and nodes using IPv4 or IPv6 UDP unicast or multicast.

Aprsdigi implements conventional packet radio AX.25 digipeating, in which a packet is digipeated if the next hop (non-repeated) digipeater ("via") callsign matches the AX.25 port's callsign and sub-station ID (SSID) or an alias callsign and SSID.

There are a number of extensions to conventional digipeating that have been proposed for use in the APRS community. Some of these features have been adopted by Terminal Node Controller (TNC) manufacturers, notably Paccomm and Kantronics. Aprsdigi implements most if not all of the commercialy adopted and proposed features. See the APRS 1.0 Protocol Specification at www.tapr.org for protocol documentation. Aprsdigi attempts to minimally comply with the protocol specification as well as support experimental APRS features. Specific features implemented include:

•

Single-interface conventional UI-frame digipeating.

•

Cross-interface digipeating (also known as bridging, routing or gatewaying) and one-to-many fanout.

•

Substitution of a digipeated alias with the interface's callsign (typically used to substitute RELAY, WIDE or TRACE aliases).

•

WIDEn-n flooding algorithim.

•

TRACEn-n route recording.

•

Mic-Encoder(tm) support, including SSID-based digipeating, decompression of packets into the conventional APRS MIM format. (The Mic-Encoder compression is also used by other products such as the Kenwood TH-D7A and D700, and TAPR PIC-Encoder).

•

TheNet X1J4 node beacon text translation (removal of the TheNet X1J4 (alias) prefix from the btext).

-v --verbose

Produce verbose debugging output.

-T --testing

Test mode: listen to my packets too. This mode is useful for off-air experimentation and configuration testing. Do not use it on-air.

-D --kill_dupes

Suppress Duplicate packets. Remembers duplicate packets for the number of seconds given by the -k option and will not repeat them more than once. This reduces conjestion caused when several digipeaters that share a common flooding alias (e.g. WIDE) have overlapping footprints, causing geometric duplication of packets addressed via WIDE,WIDE for example.

-L --kill_loops

Suppress Looping packets. Similar in function to duplicate packet suppression, but looks back through the list of already digipeated callsigns in the packet's digipeat list and kills any packets that list a callsign belonging to this aprsdigi. Note that only real callsigns are compared. Generic flooding aliases are not. Therefore, loop detection is only useful when callsign substitution is used.

-V --version

Print program version and exit.

-n|s|e|w --north|south|east|west

Set North|South|East|West SSID directional path.

-d --digipath

Set SSID omnidirectional next-hops when operating in a non flooding network (e.g. when WIDEn-n is not an option).

-f --flood

Set flooding alias. Use -f WIDE to enable WIDEn-n flooding. Use -f multiple times to define several flooding aliases.

-F --trace

Set flooding trace callsign. Use -F TRACE to enable TRACE and TRACEn-n flooding. Use -F multiple times to define several trace aliases.

-k --keep secs

Remember old packets for this long for duplicate packet detection. Default is 28 seconds.

-l --logfile file

Log digipeated packets to this file.

Put these options before each -p --interface to set new values as needed. The values you set are remembered for subsequent -p's so options you want to set for all interfaces need only be specified once, before the first -p. But you have to remember to unset an option if you don't want it to apply to subsequent interfaces.

-C (-c) --[no]subst_mycall

Do (not) perform callsign substitution. When enabled, aliases are replaced with the interface's callsign when repeated.

-M (-m) --[no]mice_xlate

Do (not) perform Mic-E to MIM translation. When enabled, compressed Mic-E reports are expanded into one MIM-style position report packet and optionally a second telemetry packet if telemetry was supplied in the Mic-E packet.

-X (-x) --[no]x1j4_xlate

Do (not) perform X1J4 translation. When enabled, the leading TheNet X1J4 (alias) text is removed when digipeated. This allows non-compliant APRS implementations to detect an APRS position report in an X1J4 beacon.

-i --idinterval secs

Seconds between ID transmissions. Set to 0 to disable IDs on this interface. Default is 570 (9 minutes 30 seconds). IDs are only sent if the interface transmitted anything since the last ID. ID packets are addressed to the ID callsign, have no digipeat path, and list the callsign and aliases for the interface the ID is being transmitted on.

-t --tag text

Text to append to received packets. Use -t - to reset to empty. Use this, for example, when gatewaying Mic-E packets from a voice repeater to the APRS net frequency to indicate where the report originated.

-3 --3rdparty

Enable 3rd party tunneling. Packets tunneled to a 3rd party interface are sent with the unused digipeaters removed from the digipeater list. Packets tunneled from a 3rd party interface have the Source Path Header prepended to the packet payload prefixed by the "}" character.

-0 --no3rdparty

Enable transparent tunneling. No special tricks are done when sending to or receiving from a tunneled interface. If the interface does not natively support AX.25 addresses (from-call, to-call, and digipeater list), then the address header is prepended to the payload in "cooked" format. Likewise, a cooked prepended header is stripped from a cooked interface and put back in the AX.25 address when going from a non-AX.25 to AX.25 interface.

-o r --norx

Disable receiving on the following interface(s).

-o R --rx

Enable receiving on the following interface(s).

-o t --notx

Disable transmitting on the following interface(s).

-o T --tx

Enable transmitting on the following interface(s).

-o s --notxsame

Disable retransmitting a received packet on the same interface.

-o S --txsame

Enable retransmitting a received packet on the same interface.

-o d --duplicate intf

Duplicate received packets without modification to the given interface (port).

-p --interface ax25:port:alias1,alias2,...

AX25 interface name (port) and optional list of aliases. The primary callsign is obtained from the interface's configuration. (See ifconfig(8)).

-p --interface udp:host/port/ttl:alias1,alias2,...

IP host name or address and list of aliases. IP addresses may be IPv4 unicast or multicast or IPv6 unicast. The primary callsign is obtained from the first alias.

-p --interface unix:filename:alias1,alias2,...

Unix file and list of aliases. Useful for debugging by setting up a simulated APRS network on one machine. You may want to make your FIFOs explicitly transmit- or receive-only to avoid confusion. The primary callsign is obtained from the first alias.

-B|b --[no]bud

addr Is similar to a TNC-2's BUDLIST. Use -B --bud to accept or -b --nobud to ignore packets from a sender or group of senders. Budlists are attached to each interface and can be reset with --bud -

You can set up a global budlist once, or per-interface budlists. The format of addr varies based on the interface type: --bud ax25:callsign-ssid matches only a given digipeater callsign and SSID. For example, -B ax25:n0clu-14. --bud ax25:callsign matches all SSIDs for the given callsign. For example -B ax25:n0clu. --bud ip:hostname matches one Internet host name (IPv6 or IPv4). For example -B ip:n0clu.ampr.net --bud ip:address/maskbits matches all IP addresses that have the given prefix. For example --bud ip:44.0.0.0/8 matches the entire class-A network. --bud ip:192.168.0.0/16 matches the entire class-B network. --bud ip:fe80::201:3ff:fe9a:38c6 matches a single IPv6 host. --bud ip:2002:905::/32 matches the 32-bit IPv6 prefix.

aprsdigi responds to the following signals:

SIGUSR1

Print cumulative statistics. For each port, the following counters are displayed: packets received and how many of those where ignored, duplicates, loops, mic-E formatted; packets transmitted and how many of those where conventional digipeats, flooding digipeats (WIDEn-n), SSID-based digipeats, and IDs. If a log file was specified with the -l --logfile option, then the statistics are written to that file. Otherwise they are written to stderr.

SIGUSR2

Prints the statistics and then resets all counters to zero.

All other normal termination signals cause final statistics to print before aprsdigi exits.

SSID-based routing uses a non-zero sub-station ID in the destination callsign, an empty digipeater path to indicate that the APRS digipeater should repeat the packet after filling in an appropriate digipeater path. For example, a packet sent to T1QS4W-3 would be repeated with a modifed destination of APRS VIA WIDE3-3 (in a network that supports WIDEn-n flooding). A packet sent to APRS-11 would be repeated to the West unproto path, as defined with the --west option. A table of SSID values and their paths follows:

SSID unproto path
---- ------------
0    none 
1    WIDE1-1
2    WIDE2-2
3    WIDE3-3
4    WIDE4-4
5    WIDE5-5
6    WIDE6-6
7    WIDE7-7
8    NORTH UNPROTO path
9    SOUTH UNPROTO path
10   EAST  UNPROTO path
11   WEST  UNPROTO path
12   NORTH UNPROTO path + WIDE
13   SOUTH UNPROTO path + WIDE
14   EAST  UNPROTO path + WIDE
15   WEST  UNPROTO path + WIDE

Aprsdigi also fits into a non WIDEn-n network by using the same algorithm for selection of subset of digipeaters from a list supplied with the --digipath option as the MIC-E. That is, SSIDs of 1, 2 or 3 select that number of digipeaters from the first three digipeaters in the --digipath list. SSIDs of 4, 5, 6, or 7, start at the fourth digipeater in the list.

APRS flooding (WIDEn-n) digipeating works by repeating any received packet whose next hop digipeater has a flooding alias (specified with the --flood option), and the SSID is 1 or greater. The SSID is decremented by one, and the packet is repeated. Furthermore, to prevent broadcast storms, recently transmitted packets are remembered for a period of time specified by the --keep option and are not repeated if they are heard within that time period.

Unlike conventional digipeating, in which the digipeater callsign/alias is flagged as repeated, the flooding mode does not do this. Once the SSID decrements to zero, then a flooding alias is treated just like any other alias, and does get marked as repeated upon transmission.

Flooding Trace aliases (TRACEn-n; --trace option) are treated like flooding aliases with the addition that, besides decrementing the SSID, the current interface's callsign is inserted in front of the trace alias, providing a record-route function. Plain trace aliases (TRACE; also --trace option) are simply substituted in the conventional ( --subst_mycall ) manner.

In single port operation, there is only one interface specified with --interface. All packets are received and some are retransmitted on the same interface, depending on whether they match the criteria for retransmission after translation of the digpeater path from one of the APRS-specific formats:

•

Mic-E TO-call SSID-based route.

•

WIDEn-n/TRACEn-n flooding.

or a conventional next-hop (non-repeated) digipeater matching the callsign or one of the aliases for the interface.

The decision to transmit is made by matching the next hop callsign/alias with the table of callsigns and aliases you supply to --interface.

In multi-port operation, this same technique simply extends to several interfaces. Besides each interface's unique callsign, you can give the same alias to several interfaces. This results in a one-to-many fanout which might be useful for dual frequency operation such as a general use APRS net frequency and an event-specific frequency.

By using different flags for Mic-E expansions, etc. you can tailor these fanouts differently on each of these interfaces, perhaps keeping Mic-E packets compressed on one frequency while decompressing them on another.

The --dupe intf option will duplicate a packet received on one interface to the interface name given. If you want to duplicate to several other interface, repeat --dupe intf for each interface. The packet is duplicated verbatim as received. No callsign substitution, flooding or other processing or checking such as whether the packet still has any non-repeated digipeaters in the list is checked. This feature is meant to provide a means to simply repeat received packets verbatim, on an RF interface, for example, out an interface that might be an Ethernet, that has APRS client applications running on it (or aprsd listening on a UDP interface). Digipeating without the normal processing can be dangerous since the digipeater list is never used up. Because of this, packets received on a given interface will never be blindly duplicated back to the same interface, regardless of the option setting.

Note that TRACEn-n vs. plain TRACE do different things: TRACEn-n *inserts* calls into the digipath while decrementing ssid, e.g.:

	RELAY*,TRACE3-3
	RELAY,N2YGK-7*,TRACE3-2
	RELAY,N2YGK-7,WB2ZII*,TRACE3-1
	RELAY,N2YGK-7,WB2ZII,N2MH-15*,TRACE3
	RELAY,N2YGK-7,WB2ZII,N2MH-15,WA2YSM-14*

Kill looping packets (--kill_loops option):

	RELAY*,WIDE,WIDE,WIDE
	RELAY,N2YGK-7*,WIDE,WIDE
	RELAY,N2YGK-7,WIDE*,WIDE

Following is a sample invocation of aprsdigi running on two ports. This is a contrived example that tries to show all the features. Comments to the right describe each feature.

aprsdigi \
   --verbose \                                 # verbose
   --north "N2YGK-2 WB2ZII WA2YSM-14" \        # North digi path
   --south "N2YGK-3 WB2ZII WA2JNF-4" \         # South ...
   --east "N2YGK-3 WB2ZII KD1LY" \             # East ...
   --west "N2YGK-2 WB2ZII N2MH-15" \           # West ...
   --flood "WIDE" \                            # WIDEn-n flooding
   --trace "TRACE" \                           # TRACEn-n tracing
   --kill_dupes \                              # kill dupes
   --kill_loops \                              # kill loops
   --mice_xlate \                              # do Mic-E translation
   --subst_mycall \                            # do callsign substituton
   --tag " via 147.06 (WB2ZII/R)" \            # add this tag to rec'd pkts
   --nobud "ax25:NOCALL" \                     # ignore pkts from NOCALL
   --dupe udp:233.0.14.100 \			# dupe everything heard 
   --int ax25:sm0:RELAY,WIDE,TRACE \           # ax25 soundmodem intf
   --nomice_xlate \                            # turn off Mic-E translation
   --x1j4_xlate \                              # do X1J4 translation
   --nosubst_mycall \                          # turn off callsign subst.
   --tag - \                                   # clear the tag
   --int ax25:ax0:RELAY,WIDE,FOO,TRACE \       # ax25 ax0 intf.
   --bud - \                                   # clear the budlist
   --bud ip:128.59.39.150/32 \                 # allow only from this IP host
   --int udp:233.0.14.99/12345/16:N2YGK-4,RELAY,WIDE,TRACE \ # multicast 
   --int udp:233.0.14.100/12345/16:N2YGK-5	# to this mcast group

opening UDP socket on 233.0.14.99/12345/16 UDP address info: family 2 type 2 proto 17 next 0x0 Linux APRS(tm) digipeater Copyright (c) 1996,1997,1999,2001,2002,2003 Alan Crosswell, n2ygk@weca.org Version: aprsdigi aprsdigi-2.4.3 This is free software covered under the GNU Public License. There is no warranty. See the file COPYING for details.

# configuration: budlist 1 deny NOCALL/48 budlist 2 permit 128.59.39.150/32 interface ax25:sm0 callsign N2YGK-2 alias RELAY alias WIDE alias TRACE option SUBST_MYCALL on option MICE_XLATE on option X1J4_XLATE off option I_TX on option I_RX on option I_TXSAME on option idinterval 570 #(09:30) option tag via 147.06 (WB2ZII/R) budlist 1 interface ax25:ax0 callsign N2YGK-3 alias RELAY alias WIDE alias FOO option SUBST_MYCALL off option MICE_XLATE off option X1J4_XLATE on option I_TX on option I_RX on option I_TXSAME on option idinterval 570 #(09:30) option tag #(none) budlist 2 interface udp:233.0.14.99 callsign N2YGK-4 alias RELAY alias WIDE alias FOO option SUBST_MYCALL off option MICE_XLATE off option X1J4_XLATE on option I_TX on option I_RX on option I_TXSAME off option idinterval 570 #(09:30) option tag #(none) budlist 2 # end of configuration

My callsigns and aliases (routing table): Callsign Interfaces... N2YGK-2 sm0 RELAY sm0 ax0 233.0.14.99 WIDEn-n sm0 ax0 233.0.14.99 TRACEn-n sm0 N2YGK-3 ax0 FOO ax0 233.0.14.99 N2YGK-4 233.0.14.99 SSID-based directional routing:

N: N2YGK-2 WB2ZII WA2YSM-14 S: N2YGK-3 WB2ZII WA2JNF-4 E: N2YGK-3 WB2ZII KD1LY W: N2YGK-2 WB2ZII N2MH-15 keep dupes for: 28 seconds log file: (none) kill dupes: ON loops: ON testing: OFF

Aprsdigi should not be confused with a Wes Johnson's DOS program of the same name. This code has most recently been tested with the Linux 2.4.20 kernel under Red Hat Fedora Core 1. The command line syntax is ugly and will eventually be replaced by a configuration file. Short options are deprecated and will dissappear in a future release. Please use long options.

/etc/ax25/axports

call(1), listen(1), beacon(1), ax25(4), kissattach(8), ifconfig(8), aprsmon(1), http://www.tapr.org

Alan Crosswell, n2ygk@weca.org



APRS and the Mic-Encoder are Trademarks of APRS Engineering LLC.