The following options are available:

-d

enables debugging output. Additional -d options increase the number of messages.

-D

indicates that dccd() started .

-F

uses read() and write() instead of mmap() in some cases to access the DCC database. This works better on some versions of Solaris provided the entire DCC database fits in RAM and provided the file system has not been tuned for the large, random accesses of a DCC database. It is the default on Solaris.

-f

turns off -F .

-N

creates a new, empty database. There must not be an existing database and the DCC server, dccd(8) , must not be running.

-R

repairs a database.

-P

expires old checksums from a database using the -e , -E , and -t values from the preceding use of dbclean . -P cannot be used with -e , -E , or -t . Note also that using -P differs from not using -e -E or -t , because in the absence of all four, their default values are used.

-S

says that the DCC server, dccd(8) , is not running and so should run stand-alone and not try to tell the DCC server about changes to the database. -i is not needed when -S is present.

-V

displays the version of the DCC database cleaner.

-q

quiets the announcement of results at the end.

-i id

specifies the DCC ID recognized by the local DCC server as its own. This ID allows the DCC server to recognize commands from to stop using the database while it is being cleaned.

-a Xo

[server-addr] [,port] is commonly used to specify a UDP port or IP address of the local server other than the default.

-h homedir

overrides the default DCC home directory, which is often /var/dcc.

-G on

cleans a greylist database.

-s hash-size

specifies a size for the hash table. By default the hash table is rebuilt to be approximately 80% full based on an estimate of the number of distinct checksums in the main file.

-e seconds

specifies that reports older than seconds and with totals below their -t thresholds should be deleted. Reports older than seconds of checksums that have been reported more recently are summarized in the database. The default value is 2 days or the value of -E , whichever is smaller. The 2 day default is reduced if the system does not appear to have enough RAM to hold the database. The minimum is 1 hour. Seconds can also be NEVER or a number of hours, days, or weeks followed by HOURS , H , DAYS , D , WEEKS or W . DCC servers that are not very busy and are isolated or do not receive "floods" of checksums from busy servers should use longer values to increase their chances of recognizing bulk mail.

-E spamsecs

changes the expiration of checksums exceding -t thresholds from the default of 30 days or the explicit value of -e , whichever is larger. The 30 day default is reduced if the system does not have enough RAM to hold the database. Spamsecs can also be NEVER or a number of hours, days, or weeks followed by HOURS , H , DAYS , D , WEEKS or W .

-t type,allsecs Ns [,threshold,bulksecs]

overrides the global -e setting and specifies that reports of checksums of type with total counts of at least threshold should be kept for bulksecs seconds. All reports should be kept for the shorter duration, allsecs seconds. The threshold is either a number or the string MANY indicating millions of targets. By default acts as if given -t Fuz1,seconds,20,spamsecs -t Fuz2,seconds,20,spamsecs , where seconds is the value for -e and spamsecs is the value for -E . All other checksum types act as if -t type,seconds were specified. Allsecs and bulksecs can also be NEVER or a number of hours, days, or weeks followed by HOURS , H , DAYS , D , WEEKS or W .

-L ltype,facility.level

specifies how messages should be logged. Ltype must be error or info to indicate which of the two types of messages are being controlled. Level must be a syslog() level among EMERG , ALERT , CRIT , ERR , WARNING , NOTICE , INFO , and DEBUG . Facility must be among AUTH , AUTHPRIV , CRON , DAEMON , FTP , KERN , LPR , MAIL , NEWS , USER , UUCP , and LOCAL0 through LOCAL7 . The default is equivalent to

exits 0 on success, and > 0 if an error occurs.