ntfsresize - resize an NTFS filesystem without data loss

ntfsresize [OPTIONS] --info DEVICE

ntfsresize [OPTIONS] [--size SIZE[k|M|G]] DEVICE

The ntfsresize program safely resizes Windows XP, Windows Server 2003, Windows 2000, Windows NT4 and Longhorn NTFS filesystems without data loss. All NTFS versions are supported, used by 32-bit and 64-bit Windows. Defragmentation is NOT required prior to resizing because the program can relocate any data if needed, without risking data integrity.

Ntfsresize can be used to shrink or enlarge any NTFS filesystem located on an unmounted DEVICE (usually a disk partition). The new filesystem will have SIZE bytes. The SIZE parameter may have one of the optional modifiers k, M, G, which means the SIZE parameter is given in kilo-, mega- or gigabytes respectively. Ntfsresize conforms to the SI, ATA, IEEE standards and the disk manufacturers by using k=10^3, M=10^6 and G=10^9.

If both --info and --size are omitted then the NTFS filesystem will be enlarged to the underlying DEVICE size.

To resize a filesystem on a partition, you must resize BOTH the filesystem and the partition by editing the partition table on the disk. Similarly to other command line filesystem resizers, ntfsresize doesn't manipulate the size of the partitions, hence to do that you must use a disk partitioning tool as well, for example fdisk(8). Alternatively you could use one of the many user friendly partitioners that uses ntfsresize internally, like Mandriva's DiskDrake, QTParted, SUSE/Novell's YaST Partitioner, IBM's EVMS, GParted or Debian/Ubuntu's Partman.

IMPORTANT! It's a good practice making REGULAR BACKUPS of your valuable data, especially before using ANY partitioning tools. To do so for NTFS, you could use ntfsclone(8). Don't forget to save the partition table as well!

If you wish to shrink an NTFS partition, first use ntfsresize to shrink the size of the filesystem. Then you could use fdisk(8) to shrink the size of the partition by deleting the partition and recreating it with the smaller size. Do not make the partition smaller than the new size of NTFS otherwise you won't be able to boot. If you did so notwithstanding then just recreate the partition to be as large as NTFS.

To enlarge an NTFS filesystem, first you must enlarge the size of the underlying partition. This can be done using fdisk(8) by deleting the partition and recreating it with a larger size. Make sure it will not overlap with an other existing partition. Then you may use ntfsresize to enlarge the size of the filesystem.

When recreating the partition by a disk partitioning tool, make sure you create it at the same starting sector and with the same partition type as before. Otherwise you won't be able to access your filesystem. Use the 'u' fdisk command to switch to the reliable sector unit from the default cylinder one.

Also make sure you set the bootable flag for the partition if it existed before. Failing to do so you might not be able to boot your computer from the disk.

Below is a summary of all the options that ntfsresize accepts. All options have two equivalent names. The short name is preceded by - and the long name is preceded by --. Any single letter options, that don't take an argument, can be combined into a single command, e.g. -fi is equivalent to -f -i.

-i, --info

By using this option ntfsresize will determine the theoretically smallest shrunken filesystem size supported. Most of the time the result is the space already used on the filesystem. Ntfsresize will refuse shrinking to a smaller size than what you got by this option and depending on several factors it might be unable to shrink very close to this theoretical size. Although the integrity of your data should be never in risk, it's still strongly recommended to make a test run by using the --no-action option before real resizing.

Practically the smallest shrunken size generally is at around "used space" + (20-200 MB). Please also take into account that Windows might need about 50-100 MB free space left to boot safely.

This option never causes any changes to the filesystem, the partition is opened read-only.

-s, --size SIZE[k|M|G]

Resize filesystem to size[k|M|G] bytes. The optional modifiers k, M, G mean the SIZE parameter is given in kilo-, mega- or gigabytes respectively. Conforming to standards, k=10^3, M=10^6 and G=10^9. Use this option with --no-action first.

-f, --force

Forces ntfsresize to proceed with the resize operation even if the filesystem is marked for consistency check.

Please note, ntfsresize always marks the filesystem for consistency check before a real resize operation and it leaves that way for extra safety. Thus if NTFS was marked by ntfsresize then it's safe to use this option. If you need to resize several times without booting into Windows between each resizing steps then you must use this option.

-n, --no-action

Use this option to make a test run before doing the real resize operation. Volume will be opened read-only and ntfsresize displays what it would do if it were to resize the filesystem. Continue with the real resizing only if the test run passed.

-b, --bad-sectors

Support disks having hardware errors, bad sectors with those ntfsresize would refuse to work by default.

Prior using this option, it's strongly recommended to make a backup by ntfsclone(8) using the --rescue option, then running 'chkdsk /f /r volume:' on Windows from the command line. If the disk guarantee is still valid then replace it. It's defected. Please also note, that no software can repair these type of hardware errors. The most what they can do is to work around the permanent defects.

This option doesn't have any effect if the disk is flawless.

-P, --no-progress-bar

Don't show progress bars.

-v, --verbose

More output.

-h, --help

Display help and exit.

The exit code is 0 on success, non-zero otherwise.

No reliability problem is known. If you need help please try the Ntfsresize FAQ first (see below) and if you don't find your answer then send your question, comment or bug report to <linux-ntfs-dev@lists.sourceforge.net>. No subscription is needed but the mailing list is moderated and it can take a short time to approve your post.

There are a few very rarely met restrictions at present: filesystems having unknown bad sectors, relocation of the first MFT extent and resizing into the middle of a $MFTMirr extent aren't supported yet. These cases are detected and resizing is restricted to a safe size or the closest safe size is displayed.

Ntfsresize schedules an NTFS consistency check and after the first boot into Windows you must see chkdsk running on a blue background. This is intentional and no need to worry about it. Windows may force a quick reboot after the consistency check. Moreover after repartitioning your disk and depending on the hardware configuration, the Windows message System Settings Change may also appear. Just acknowledge it and reboot again.

The disk geometry handling semantic (HDIO_GETGEO ioctl) has changed in an incompatible way in Linux 2.6 kernels and this triggered multitudinous partition table corruptions resulting in unbootable Windows systems, even if NTFS was consistent, if parted(8) was involved in some way. This problem was often attributed to ntfsresize but in fact it's completely independent of NTFS thus ntfsresize. Moreover ntfsresize never touches the partition table at all. By changing the 'Disk Access Mode' to LBA in the BIOS makes booting work again, most of the time. You can find more information about this issue in the Troubleshooting section of the below referred Ntfsresize FAQ.

Ntfsresize has been written by Szabolcs Szakacsits <szaka@sienet.hu>.

Many thanks to Anton Altaparmakov and Richard Russon for libntfs, the excellent documentation and comments, to Gergely Madarasz, Dewey M. Sasser and Miguel Lastra and his colleagues at the University of Granada for their continuous and highly valuable help, furthermore to Erik Meade, Martin Fick, Sandro Hawke, Dave Croal, Lorrin Nelson, Geert Hendrickx, Robert Bjorkman and Richard Burdick for beta testing the relocation support, to Florian Eyben, Fritz Oppliger, Richard Ebling, Sid-Ahmed Touati, Jan Kiszka, Benjamin Redelings, Christopher Haney, Ryan Durk, Ralf Beyer for the valued contributions and to Theodore Ts'o whose resize2fs(8) man page originally formed the basis of this page.

Ntfsresize is part of the ntfsprogs(8) package and is available from http://linux-ntfs.sourceforge.net/ as source and precompiled binary. Ntfsresize related news, example of usage, troubleshooting, statically linked binary and FAQ (frequently asked questions) is maintained at http://mlf.linux.rulez.org/mlf/ezaz/ntfsresize.html

fdisk(8), cfdisk(8), sfdisk(8), parted(8), evms(8), ntfsclone(8), mkntfs(8), ntfsprogs(8)