dict - DICT Protocol Client

dict word



dict [options] [word]



dict [options] dict://host:port/d:word:database



dict [options] dict://host:port/m:word:database:strategy

dict is a client for the Dictionary Server Protocol (DICT), a TCP transaction based query/response protocol that provides access to dictionary definitions from a set of natural language dictionary databases. dict uses the system's default pager ($PAGER) to display responses. This default behavior may be modified in the configuration file or on the command line. Exit status is 0 if operation succeeded, or non-zero otherwise.

See EXIT STATUS section.

-h server or --host server

Specifies the hostname for the DICT server. Server/port combinations can be specified in the configuration file. If no servers are specified in the configuration file or or on the command line, dict will fail. (This is a compile-time option, ./configure --enable-dictorg, which is disabled by default.) If IP lookup for a server expands to a list of IP addresses (as dict.org does currently), then each IP will be tried in the order listed.

-p service or --port service

Specifies the port (e.g., 2628) or service (e.g., dict) for connections. The default is 2628, as specified in the DICT Protocol RFC. Server/port combinations can be specified in the configuration file.

-d dbname or --database dbname

Specifies a specific database to search. The default is to search all databases (a "*" from the DICT protocol). Note that a "!" in the DICT protocol means to search all of the databases until a match is found, and then stop searching.

-m or --match

Instead of printing a definition, perform a match using the specified strategy.

-s strategy or --strategy strategy

Specify a matching strategy. By default, the server default match strategy is used. This is usually "exact" for definitions, and some form of spelling-correction strategy for matches ("." from the DICT protocol). The available strategies are dependent on the server implementation. For a list of available strategies, see the -S or --strats option.

-C or --nocorrect

Usually, if a definition is requested and the word cannot be found, spelling correction is requested from the server, and a list of possible words are provided. This option disables the generation of this list.

-c file or --config file

Specify the configuration file. The default is to try ~/.dictrc and /etc/dict.conf (/etc/dictd/dict.conf on Debian systems), using the first file that exists. If a specific configuration file is specified, then the defaults will not be tried.

-D or --dbs

Query the server and display a list of available databases.

-S or --strats

Query the server and display a list of available search strategies.

-H or --serverhelp

Query the server and display the help information that it provides.

-i dbname or --info dbname

Request information on the specified database (usually the server will provide origination, descriptive, or other information about the database or its contents).

-I or --serverinfo

Query the server and display information about the server.

-M or --mime

Send OPTION MIME command to the server. NOTE: Server's capabilities are not checked.

-a or --noauth

Disable authentication (i.e., don't send an AUTH command).

-u user or --user user

Specifies the username for authentication.

-k key or --key key

Specifies the shared secret for authentication.

-V or --version

Display version information.

-L or --license

Display copyright and license information.

--help

Display help information.

-v or --verbose

Be verbose.

-r or --raw

Be very verbose: show the raw client/server interaction.

-P program or --pager program

Specify program to use as pager. Use "-" for none.

--pipesize

Specify the buffer size for pipelineing commands. The default is 256, which should be sufficient for general tasks and be below the MTU for most transport media. Larger values may provide faster or slower throughput, depending on MTU. If the buffer is too small, requests will be serialized. Values less than 0 and greater than one million are silently changed to something more reasonable.

--client text

Specifies additional text to be sent using the CLIENT command.

--debug flag

Set a debugging flag. Valid flags are:

verbose

The same as -v or --verbose.

raw

The same as -r or --raw.

scan

Debug the scanner for the configuration file.

parse

Debug the parser for the configuration file.

pipe

Debug TCP pipelining support (see the DICT RFC and RFC1854).

serial

Disable pipelining support.

time

Perform transaction timing.

The configuration file currently has a very simple format. Lines are used to specify servers, for example: server dict.org or, with options: server dict.org { port 8080 }

server dict.org { user username secret }

server dict.org { port dict user username secret } the port and user options may be specified in any order. The port option is used to specify an optional port (e.g., 2628) or service (e.g., dict) for the TCP/IP connection. The user option is used to specify a username and shared secret to be used for authentication to this particular server.

Servers are tried in the order listed until a connection is made. If none of the specified servers are available, and the compile-time option (./configure --enable-dictorg) is enabled, then an attempt will be made to connect on localhost and on dict.org at the standard part (2628). (This option is disabled by default.) We expect that dict.org will point to one or more DICT servers (perhaps in round-robin fashion) for the foreseeable future (starting in July 1997), although it is difficult to predict anything on the Internet for more than about 3-6 months.

The configuration file also allows the setting of a pager (keyword pager), similar to the --pager option.

0 Successful completion

20 No matches found

21 Approximate matches found

22 No databases available

23 No strategies available

30 Unexpected response code from server

31 Server is temporarily unavailable

32 Server is shutting down

33 Syntax error, command not recognized

34 Syntax error, illegal parameters

35 Command not implemented

36 Command parameter not implemented

37 Access denied

38 Authentication failed

39 Invalid database

40 Invalid strategy

41 Connection to server failed

dict was written by Rik Faith (faith@cs.unc.edu) and is distributed under the terms of the GNU General Public License. If you need to distribute under other terms, write to the author.

The main libraries used by this programs (zlib, regex, libmaa) are distributed under different terms, so you may be able to use the libraries for applications which are incompatible with the GPL -- please see the copyright notices and license information that come with the libraries for more information, and consult with your attorney to resolve these issues.

If a dict: URL is given on the command line, only the first one is used. The rest are ignored.

If a dict: URL contains a specifier for the nth definition or match of a word, it will be ignored and all the definitions or matches will be provided. This violates the RFC, and will be corrected in a future release.

If a dict: URL contains a shared secret, it will not be parsed correctly.

When OPTION MIME command is sent to the server (-M option) , server's capabilities are not checked.

~/.dictrc

/etc/dict.conf (/etc/dictd/dict.conf on Debian systems.)

dictd(8), dictzip(1), http://www.dict.org, RFC 2229