The G-Kermit binary is called "gkermit". It should be stored someplace in your UNIX PATH; normally it is available as /usr/local/bin/gkermit. To run G-Kermit, just type "gkermit" followed by command-line options that tell it what to do. If no options are given, it prints a usage message listing the available options.

If an option takes an argument, the argument is required; if an option does not take an argument, no argument may be given (exception: -d). The action options are -r, -s, and -g. Only one action option may be given. If no action options are given, G-Kermit does nothing (except possibly to print its usage message or create a debug.log file). Here are some examples ("$ " is the shell prompt):

  $ gkermit -s hello.c   <-- Send the hello.c file
  $ gkermit -s hello.*   <-- Send all hello.* files
  $ gkermit -r           <-- Wait to receive files
  $ gkermit -g hello.c   <-- Get hello.c file
  $ gkermit -g hello.\*  <-- Get all hello.* files

  $ gkermit -is hello.o  <-- Send hello.o in binary mode
  $ gkermit -dr          <-- Receive with debugging

  -r      RECEIVE.  Wait for incoming files.
  -s fn   SEND.  Send file(s) specified by fn.
  -g fn   GET.  Get specified file(s) from server.
  -a fn   AS-NAME.  Alternative name for file.
  -i      IMAGE.  Binary-mode transfer (default).
  -T      TEXT. Text-mode transfer.
  -P      PATH (filename) conversion disabled.
  -w      WRITEOVER when filenames collide.
  -K      KEEP incompletely received files.
  -p x    PARITY. x = e,o,m,s,n; default = n(one).
  -e n    PACKET LENGTH.  n = 40-9000; default=4000.
  -b n    TIMEOUT.  Per-packet timeout, seconds.
  -x      XON/XOFF.  Set Xon/Xoff in the tty driver.
  --x     Unset Xon/Xoff in the tty driver.
  -S      STREAMING disabled.
  -X      EXTERNAL.  G-Kermit is an external protocol.
  -q      QUIET.  Suppress messages.
  -d      DEBUG.  Write debugging info to ./debug.log.
  -d fn   DEBUG.  Write debugging info to given file.
  -h      HELP.  Display brief usage message.

You may supply options to G-Kermit on the command line or through the GKERMIT environment variable, which can contain any valid gkermit command-line options. These are processed before the actual command-line options and so can be overridden by them. Example for bash or ksh, which you can put in your profile if you want to always keep incomplete files, suppress streaming, suppress messages, and use Space parity:

  export GKERMIT="-K -S -q -p s"

To transfer files with G-Kermit you must be connected through a terminal emulator to the UNIX system where G-Kermit is running, meaning you are online to UNIX and have access to the shell prompt (or to a menu that has an option to invoke G-Kermit). The connection can be serial (direct or dialed) or network (Telnet, Rlogin, X.25, etc).

When you tell G-Kermit to SEND a file (or files), e.g. with:

  $ gkermit -Ts oofa.txt

• If your emulator supports Kermit "autodownloads" then it receives the file automatically and puts you back in the terminal screen when done. • Otherwise, you'll need to take whatever action is required by your emulator to get its attention: a mouse action, a keystroke like Alt-x, or a character sequence like Ctrl-\ or Ctrl-] followed by the letter "c" (this is called "escaping back") and then tell it to receive the file. When the transfer is complete, you must instruct your emulator to go back to its terminal screen.

During file transfer, most terminal emulators put up some kind of running display of the file transfer progress.

When you tell G-Kermit to RECEIVE (with "gkermit -r"), this requires you to escape back to your terminal emulator and instruct it to send the desired file(s).

If your terminal emulator supports Kermit autodownloads AND Kermit server mode, then you can use GET ("gkermit -g files...") rather than RECEIVE ("gkermit -r"), and the rest happens automatically, as when G-Kermit is sending.

G-Kermit supports file and group interruption. The method for interrupting a transfer depends on your terminal emulator. For example, while the file-transfer display is active, you might type the letter 'x' to cancel the current file and go on to the next one (if any), and the letter 'z' to cancel the group. Or there might be buttons you can click with your mouse.

When G-Kermit is in packet mode and your terminal emulator is in its terminal screen, you can also type three (3) Ctrl-C characters in a row to make G-Kermit exit and restore the normal terminal modes.

When sending files in binary mode, G-Kermit sends every byte exactly as it is stored on the disk. This mode is appropriate for program binaries, graphics files, tar archives, compressed files, etc, and is G-Kermit's default file transfer mode when sending. When receiving files in binary mode, G-Kermit simply copies each byte to disk. (Obviously the bytes are encoded for transmission, but the encoding and decoding procedures give a replica of the original file after transfer.)

When sending files in text mode, G-Kermit converts the record format to the common one that is defined for the Kermit protocol, namely lines terminated by carriage return and linefeed (CRLF); the receiver converts the CRLFs to whatever line-end or record-format convention is used on its platform. When receiving files in text mode, G-Kermit simply strips carriage returns, leaving only a linefeed at the end of each line, which is the UNIX convention.

When receiving files, the sender's transfer mode (text or binary) predominates if the sender gives this information to G-Kermit in a Kermit File Attribute packet, which of course depends on whether your terminal emulator's Kermit protocol has this feature. Otherwise, if you gave a -i or -T option on the gkermit command line, the corresponding mode is used; otherwise the default mode (binary) is used.

Furthermore, when either sending or receiving, G-Kermit and your terminal emulator's Kermit can inform each other of their OS type (UNIX in G-Kermit's case). If your emulator supports this capability, which is called "automatic peer recognition", and it tells G-Kermit that its platform is also UNIX, G-Kermit and the emulator's Kermit automatically switch into binary mode, since no record-format conversion is necessary in this case. Automatic peer recognition is disabled automatically if you include the -i (image) or -T (text) option.

When sending, G-Kermit sends all files in the same mode, text or binary. There is no automatic per-file mode switching. When receiving, however, per-file switching occurs automatically based on the incoming Attribute packets, if any (explained below), that accompany each file.

When SENDING a file, G-Kermit obtains the filenames from the command line. It depends on the shell to expand metacharacters (wildcards and tilde).

G-Kermit uses the full pathname given to find and open the file, but then strips the pathname before sending the name to the receiver. For example:

  $ gkermit -s /etc/hosts

However, if a pathname is included in the -a option, the directory part is not stripped:

  $ gkermit -s /etc/hosts -a /tmp/hosts

When RECEIVING a file, G-Kermit does NOT strip the pathname. If the incoming filename includes a path, G-Kermit tries to store the file in the specified place. If the path does not exist, the transfer fails. The incoming pathname can, of course, be overridden with the -a option.

When sending a file, G-Kermit normally converts outbound filenames to common form: uppercase, no more than one period, and no funny characters. So, for example, gkermit.tar.gz would be sent as GKERMIT_TAR.GZ.

When receiving a file, if the name is all uppercase, G-Kermit converts it to all lowercase. If the name contains any lowercase letters, G-Kermit leaves the name alone.

If the automatic peer recognition feature is available in the terminal emulator, and G-Kermit recognizes the emulator's platform as UNIX, G-Kermit automatically disables filename conversion and sends and accepts filenames literally.

You can force literal filenames by including the -P option on the command line.

When G-Kermit receives a file whose name is the same as that of an existing file, G-Kermit "backs up" the existing file by adding a unique suffix to its name. The suffix is ".~n~", where n is a number. This kind of backup suffix is compatible with GNU EMACS and various other popular applications.

To defeat the backup feature and have incoming files overwrite existing files of the same name, include the -w (writeover) option on the command line.