r.buffer - Creates a raster map layer showing buffer zones surrounding cells that contain non-NULL category values.

r.buffer

r.buffer help

r.buffer [-qz] input=float output=string distances=float[,float,...] [units=string]

Flags:

Parameters:

r.buffer creates a new raster map layer showing buffer (a.k.a. "distance" or "proximity") zones around all cells that contain non-NULL category values in an existing raster map layer. The distances of buffer zones from cells with non-zero category values are user-chosen. Suppose, for example, that you want to place buffer zones around roads. This program could create the raster map layer shown below on the right based on road information contained in the raster map layer shown on the left.

000000000000000000000000 222233333333333333444444

111000000000000000000000 111222222222223333333333

000111111111100000000000 222111111111122223333333

000000001000011100000000 332222221222211122222222

000000001000000011111111 333333321233222211111111

000000001000000000000000 433333321233333222222222

000000001000000000000000 444443321233333333333333

000000001000000000000000 444443321233443333333333

000000001000000000000000 444443321233444444444444

Category 0: No roads

Category 1: Road location

Category 2: Buffer Zone 1 around roads

Category 3: Buffer Zone 2 around roads

Category 4: Buffer Zone 3 around roads

The user can run the program interactively by simply typing r.buffer without program arguments on the command line. The program then prompts the user for parameter values.

You are requested to identify the existing raster map layer from which distance-from calculations shall be based, and a name (of your choice) for the new raster map layer which will contain the results.

Then, identify the units of measurement in which buffer (distance) zones are to be calculated, and the distance of each buffer zone from each non-NULL cell in the input map. The user has the option of identifying up to 60 continuous zones. The zones are identified by specifying the upper limit of each desired zone (r.buffer assumes that 0 is the starting point). ("Continuous" is used in the sense that each category zone's lower value is the previous zone's upper value. The first buffer zone always has distance 0 as its lower bound.) Distances can be entered in one of five units: meters, kilometers, feet, miles, and nautmiles (nautical miles).

Last, calculate distances from cells containing user-specified category values, using the "fromcell" method. [The "fromcell" method goes to each cell that contains a category value from which distances are to be calculated, and draws the requested distance rings around them. This method works very fast when there are few cells containing the category values of interest, but works slowly when there are numerous cells containing the category values of interest spread throughout the area.]

The user can run r.buffer specifying all parameter values on the command line (see above).

In the example below, the buffer zones would be (in the default units of meters): 0-100, 101-200, 201-300, 301-400 and 401-500.

"

r.buffer [-q] input=name output=name distances=value[,value,...]

"

r.buffer input=roads output=roads.buf distances=100,200,300,400,500 units=meters

"

r.cats input=roads.buf

1 distances calculated from these locations

2 0-100 meters

3 100-200 meters

4 200-300 meters

5 300-400 meters

6 400-500 meters

r.buffer measures distances from center of cell to center of cell using Euclidean distance measure for planimetric databases (like UTM) and using ellipsoidal geodesic distance measure for latitude/longitude databases.

r.buffer calculates distance zones from all cells having non-NULL category values in the input map. If the user wishes to calculate distances from only selected input map layer category values, the user should run (for example) r.reclass prior to r.buffer, to reclass all categories from which distance zones are not desired to be calculated into category NULL.

g.region

r.mapcalc

r.reclass

Michael Shapiro, U.S. Army Construction Engineering Research Laboratory

James Westervelt, U.S. Army Construction Engineering Research Laboratory

Last changed: $Date: 2004/05/25 13:03:03 $

Help Index