knockd - port-knock server

knockd [options]

knockd is a port-knock server. It listens to all traffic on an ethernet (or PPP) interface, looking for special "knock" sequences of port-hits. A client makes these port-hits by sending a TCP (or UDP) packet to a port on the server. This port need not be open -- since knockd listens at the link-layer level, it sees all traffic even if it's destined for a closed port. When the server detects a specific sequence of port-hits, it runs a command defined in its configuration file. This can be used to open up holes in a firewall for quick access.

-i, --interface <int>

Specify an interface to listen on. The default is eth0.

-d, --daemon

Become a daemon. This is usually desired for normal server-like operation.

-c, --config <file>

Specify an alternate location for the config file. Default is /etc/knockd.conf.

-D, --debug

Ouput debugging messages.

-l, --lookup

Lookup DNS names for log entries. This may be a security risk! See section SECURITY NOTES.

-v, --verbose

Output verbose status messages.

-V, --version

Display the version.

-h, --help

Syntax help.

knockd reads all knock/event sets from a configuration file. Each knock/event begins with a title marker, in the form [name], where name is the name of the event that will appear in the log. A special marker, [options], is used to define global options.

[options]
	logfile = /var/log/knockd.log

[openSSH] sequence = 7000,8000,9000 seq_timeout = 10 tcpflags = syn command = /sbin/iptables -A INPUT -s %IP% -j ACCEPT

[closeSSH] sequence = 9000,8000,7000 seq_timeout = 10 tcpflags = syn command = /sbin/iptables -D INPUT -s %IP% -j ACCEPT

[options]
	logfile = /var/log/knockd.log

[opencloseSSH] sequence = 2222:udp,3333:tcp,4444:udp seq_timeout = 15 tcpflags = syn,ack start_command = /usr/sbin/iptables -A INPUT -s %IP% -p tcp --syn -j ACCEPT cmd_timeout = 5 stop_command = /usr/sbin/iptables -D INPUT -s %IP% -p tcp --syn -j ACCEPT

[options]
	logfile = /var/log/knockd.log

[opencloseSMTP] one_time_sequences = /etc/knockd/smtp_sequences seq_timeout = 15 tcpflags = fin,!ack start_command = /usr/sbin/iptables -A INPUT -s %IP% -p tcp --dport 25 -j ACCEPT cmd_timeout = 5 stop_command = /usr/sbin/iptables -D INPUT -s %IP% -p tcp --dport 25 -j ACCEPT

UseSyslog

Log action messages through syslog(). This will insert log entries into your /var/log/messages or equivalent.

LogFile = /path/to/file

Log actions directly to a file, usually /var/log/knockd.log.

PidFile = /path/to/file

Pidfile to use when in daemon mode, default: /var/run/knockd.pid.

Interface = <interface_name>

Network interface to listen on. Only its name has to be given, not the path to the device (eg, "eth0" and not "/dev/eth0"). Default: eth0.

Sequence = <port1>[:<tcp|udp>][,<port2>[:<tcp|udp>] ...]

Specify the sequence of ports in the special knock. If a wrong port with the same flags is received, the knock is discarded. Optionally, you can define the protocol to be used on a per-port basis (default is TCP).

One_Time_Sequences = /path/to/one_time_sequences_file

File containing the one time sequences to be used. Instead of using a fixed sequence, knockd will read the sequence to be used from that file. After each successful knock attempt this sequence will be disabled by writing a '#' character at the first position of the line containing the used sequence. That used sequence will then be replaced by the next valid sequence from the file.

Because the first character is replaced by a '#', it is recommended that you leave a space at the beginning of each line. Otherwise the first digit in your knock sequence will be overwritten with a '#' after it has been used.

Each line in the one time sequences file contains exactly one sequence and has the same format as the one for the Sequence directive. Lines beginning with a '#' character will be ignored.

Note: Do not edit the file while knockd is running!

Seq_Timeout = <timeout>

Time to wait for a sequence to complete in seconds. If the time elapses before the knock is complete, it is discarded.

TCPFlags = fin|syn|rst|psh|ack|urg

Only pay attention to packets that have this flag set. When using TCP flags, knockd will IGNORE tcp packets that don't match the flags. This is different than the normal behavior, where an incorrect packet would invalidate the entire knock, forcing the client to start over. Using "TCPFlags = syn" is useful if you are testing over an SSH connection, as the SSH traffic will usually interfere with (and thus invalidate) the knock.

Separate multiple flags with commas (eg, TCPFlags = syn,ack,urg). Flags can be explicitly excluded by a "!" (eg, TCPFlags = syn,!ack).

Start_Command = <command>

Specify the command to be executed when a client makes the correct port-knock. All instances of %IP% will be replaced with the knocker's IP address. The Command directive is an alias for Start_Command.

Cmd_Timeout = <timeout>

Time to wait between Start_Command and Stop_Command. This directive is optional, only required if Stop_Command is used.

Stop_Command = <command>

Specify the command to be executed when Cmd_Timeout seconds have passed since Start_Command has been executed. All instances of %IP% will be replaced with the knocker's IP address. This directive is optional.

Using the -l or --lookup commandline option to resolve DNS names for log entries may be a security risk! An attacker may find out the first port of a sequence if he can monitor the DNS traffic of the host running knockd. Also a host supposed to be stealth (eg, dropping packets to closed TCP ports instead of replying with an ACK+RST packet) may give itself away by resolving a DNS name if an attacker manages to hit the first (unknown) port of a sequence.

knock is the accompanying port-knock client, though telnet or netcat could be used for simple TCP knocks instead. For more advanced knocks, see hping, sendip or packit.

Judd Vinet <jvinet@zeroflux.org>