Each toc formatting engine has to provide a number of commands through which objects created by the package doctools::toc will upon the functionality of the engine. These commands are described here.

Management commands

toc_numpasses

This command is called by a doctoc object immediately after it has loaded the engine. No other command of the engine will be called before it. It has to return the number of passes this engine requires to fully process the input document. This value has to be an integer number greater or equal to one.

toc_initialize

This command is called at the beginning of every conversion run, as the first command of that run. Note that a run is not a pass, but may consist of multiple passes. See toc_numpasses. The command has to initialize the general state of the toc formatting engine, beyond the initialization done during the load.

toc_setup n

This command is called at the beginning of each pass over the input in a run. Its argument is the number of the pass which has begun. Passes are counted from 1 upward. The command has to set up the internal state of the toc formatting engine for this particular pass.

toc_postprocess text

This command is called immediately after the last pass in a run. Its argument is the result of the conversion generated by that pass. It is provided to allow the engine to perform any global last-ditch modifications of the generated document. The text returned by this command will be the final result of the conversion. An engine for a format which requires no postprocessing can simply return the argument without change.

toc_shutdown

This command is called at the end of every conversion run. It is the last command called in a run. It has to clean up of all the run-specific state in the toc formatting engine. After the call the engine has to be in a state which allows the initiation of another run without fear that information from the last run is leaked into this new run.

toc_listvariables

This command is called by a doctoc object after it has loaded the engine (after toc_numpasses). It has to return a list containing the names of the engine parameters provided by the engine. This list can be empty.

toc_varset varname text

This command is called whenever the doctoc object wishes to set an engine parameter to a particular value. The parameter to change is specified by varname, the value to set in text. The command has to throw an error if an unknown varname is used. Only the names returned by toc_listvariables are considered known. The values of all engine parameters have to persist between passes and runs.

Formatting commands

The commands listed in this section are responsible for the conversion of the input into the wanted output. Their names are the names of the associated markup command, with prefix fmt_ added to them. Not all markup commands have associated formatting commands. The two exceptions are vset and include. These markup commands are processed by the doctoc object itself. A detailed documentation of the markup commands can be found in the companion document doctoc_fmt. It is the formal specification of the doctoc format. Note: The formatting commands can expect that they are only called in an order allowed by the format specification.

fmt_plain_text text

This command has no associated markup command. It is called for any plain text encountered by the processor in the input. It has to perform any special processing required for plain text. The text returned as its result is added to the output. If no special processing is required it has to simply return its argument without change.

fmt_comment text

This command has to format the text as a comment and return the formatted string. It has to return the empty string if the output format has no way of formatting comments.

fmt_toc_begin text title

This command has to format the label text and the associated title string as the start of the generated table of contents and return the formatted string.

fmt_toc_end

This command has to generate the end of the generated table of contents and return the formatted string.

fmt_division_start text ?symfile?

This command has to open the beginning of a new section in the generated table of contents and return the formatted string. This opening may refer to another file, if supported by the format, and specified through symfile. An possible application of this would be to refer to a smaller table of contents just for the section. The text argument is the title of the new section.

fmt_division_end

This command has to close a section in the generated table of contents and return the formatted string.

fmt_item file text desc

This command has to format an individual toc element and return the formatted string. The document referenced by the element is specified through its symbolic name file, whereas the label to use for the link is provided by text. Use the command dt_fmap to convert the symbolic name to the actual link. It is described in section IMPORTED ENVIRONMENT. The last argument, desc, provides a short descriptive text for the referenced document.

The implementation of an toc formatting engine can make the following assumptions about the environment it is executed in:

[1]

That it has full access to its own safe interpreter. In other words, the engine cannot damage the other parts of the processor, nor can it damage the filesystem.

[2]

That the following commands are provided by the doctoc object controlling the engine:

Doctools commands

dt_format

This command returns the name of the format currently executing.

dt_fmap symfname

This command returns the actual name to use in the output in place of the symbolic filename symfname. It will return the unchanged input if no mapping was found for symfname.

dt_source file

This command allows the toc formatting engine to load additional tcl code. Only files which are either in the same directory as the file containing the engine, or below it, can be loaded. Trying to load a file outside of this directory causes an error.

Expander commands

All of the commands below are methods of the expander object (without the prefix ex_) handling the current input. This gives the engine limited access to the state of the expander. Their arguments and results are described in the documentation for the package expander.

ex_cappend

ex_cget

ex_cis

ex_cname

ex_cpop

ex_cpush

ex_cset

ex_lb

ex_rb

Other commands

The file "_toc_common.tcl" contains default implementations of fmt_plaint_text and all the toc_ commands listed in section EXPORTED COMMANDS. It resides in the subdirectory "mpformats" containing all the predefined formats. This means that all external formats (i.e. not provided by the package doctools::toc) cannot use it immediately, but have to have a copy at their location.